Tillbaka till bloggen
Gör-det-själv-guider 2026-11-20 E-Collar Technologies 0 visningar

Replacement Acorn Hex Nut: Sizing and Installation Guide

Replacement Acorn Hex Nut: Sizing and Installation Guide

Learn how to properly size and install a replacement acorn hex nut for E-Collar Comfort Pads and contact point covers. Includes compatibility details and important operational notes.

When You Need a Replacement Acorn Hex Nut

If you own an E-Collar Comfort Pad or contact point cover, the small acorn hex nut that secures the pad or cover can wear out or get lost over time. Replacing it is straightforward, but you need the correct part and an understanding of how it affects device operation.

The Replacement Acorn Hex Nut (Nylon) is designed for this exact purpose. It's a low-cost part (catalog price USD 0.88, compared to USD 1.75) that keeps your collar hardware intact.

What the Catalog Confirms About This Nut

  • Replacement Acorn Hex Nut (Nylon): This is a nylon replacement acorn hex nut for Comfort Pads or contact point covers. It confirms the nut is not a generic hardware store item; it's specifically shaped and threaded for E-Collar accessories.
    Replacement Acorn Hex Nut (Nylon)
    Replacement Acorn Hex Nut (Nylon)
  • Replacement Acorn Hex Nut (Nylon): When used as a contact post cover, no stimulation will be produced. This is a critical safety note: if you install this nut over a contact post, the collar will not deliver any stimulation. Only use it as a cover if you intentionally want to disable that post.
  • Replacement Acorn Hex Nut (Nylon): The nut is compatible with the RX-090 Small Receiver (price range $105.00 – $115.00). If you own an RX-090 receiver, this nut is the correct replacement. Other receivers may use a different thread or size.

Installation Steps

Installing the replacement acorn hex nut is a simple screw-on process. Follow these steps to ensure a secure fit.

  1. Remove the old nut: Unscrew the old nut from the Comfort Pad or contact point cover post. If it's stuck, use a small wrench or pliers gently to avoid damaging the post.
  2. Check the post condition: Inspect the threaded post for damage or debris. A clean, undamaged thread ensures the new nut will seat properly.
  3. Screw on the new nut: Hand-thread the new nylon acorn hex nut onto the post until snug. Do not overtighten; nylon can strip if forced past resistance.
  4. Verify the nut's purpose: Remember: if you are using this nut on a contact post (not a Comfort Pad), it will block stimulation. Only install it on a contact post if you intend to disable that channel.

Compatibility at a Glance

The catalog confirms this nut works with Comfort Pads and contact point covers, and it's compatible with the RX-090 Small Receiver. If you have a different receiver model, the thread size may differ. The supplied information does not list thread dimensions or compatibility with other receivers, so verify before ordering if you are unsure.

The nut is available in a Standard variant. No other options are listed in the catalog.

Honest Tradeoffs to Consider

The main tradeoff is the nut's dual use: it can secure a Comfort Pad or serve as a contact post cover, but when used as a cover it disables stimulation entirely. This is not a defect—it's by design—but it means you must be intentional about where you install it.

Also, the catalog does not specify the exact thread size or material hardness of the nylon. If you need a nut for a different application (e.g., a different brand of collar or a non-E-Collar device), this part may not fit. For E-Collar accessories, however, it is the correct replacement.

Relaterade artiklar

Customer Service
Hem
Produkter
Varukorg
Profil