Zpět na blog
Tipy a péče 2026-11-15 E-Collar Technologies 0 zobrazení

Educator Antenna and Screw Replacement: A Parts Care Guide

Educator Antenna and Screw Replacement: A Parts Care Guide

A practical guide to replacing the standard antenna, receiver gasket, and receiver screws on Educator systems, with compatibility notes and honest limits on what the parts records confirm.

Start with what actually needs replacing

Small parts fail quietly. A transmitter antenna that has been bumped or bent, a receiver gasket that no longer sits flat, or a missing receiver screw can all interrupt a training session long before the electronics give out. The trick is matching the part to the system you actually own, because these three parts are not interchangeable across every model.

The supplied records cover three distinct replacements: a standard antenna for Educator transmitters, a gasket for large RX120 receivers, and a set of four screws for RX070 receivers. Each has a different compatibility footprint, and the records do not confirm fit beyond what is stated. Treat the model names as your first filter, not your last.

The antenna: one part, all Educator transmitters

  • 1.75″ Standard Antenna for All Educator Models: The 1.75′′ standard antenna is described as a replacement antenna for all Educator models, sized small to keep the transmitter comfortable in the hand. This is the broadest-fit part of the three. If your issue is a damaged or missing transmitter antenna on an Educator system, this is the record that speaks to your case, and the compact size is a handling consideration rather than a performance claim.
    1.75″ Standard Antenna for All Educator Models
    1.75″ Standard Antenna for All Educator Models

Antenna replacement: what the record does and does not tell you

The record confirms compatibility across Educator models and notes the compact size. It does not supply a removal or installation procedure, torque guidance, or a checklist for confirming the antenna is seated correctly. That absence is a limit of the supplied information, not evidence that no procedure exists in the manufacturer documentation.

Practically, that means you should confirm the antenna is the right part for your transmitter model, then follow the fitting guidance that came with your system rather than improvising. If you are unsure whether your transmitter is an Educator model covered by this record, check the model marking before ordering. The antenna is a low-cost part, but a wrong-fit part still costs you a session.

The gasket: specific to large RX120 receivers

  • GASKET FOR LARGE RECEIVERS RX 120 ( 1 ): This gasket is listed for large receivers, RX 120. The compatibility statement is narrow. It names the RX120 receiver size, so this is not a general-purpose receiver gasket. Confirm your receiver is the large RX120 before treating this as the fix for a sealing or fit problem.
    GASKET FOR LARGE RECEIVERS RX 120 ( 1 )
    GASKET FOR LARGE RECEIVERS RX 120 ( 1 )

Gasket replacement: a fit decision before a procedure

A receiver gasket matters because it sits between the receiver housing and the environment. When it is worn, misshapen, or missing, the receiver is more exposed than it should be. The supplied record identifies the part and its receiver compatibility but does not include installation steps, cleaning requirements, or a replacement interval.

So the honest guidance is a sequence of checks rather than a script. First, confirm the receiver is the large RX120. Second, inspect the existing gasket to see whether the issue is wear, misalignment, or debris. Third, if you replace it, follow the housing guidance that came with your receiver, since the supplied information does not specify a seating method. Do not assume a gasket alone resolves a housing that is cracked or a receiver that has taken on water; those are separate questions the record does not address.

The screws: a four-piece set for RX070 receivers

  • SCREWS FOR RX070 RECEIVERS ( SET OF 4 ): This is a set of four screws listed for RX070 receivers. The quantity and the model are both part of the specification. If you are missing one screw, the set still gives you matching spares; if your receiver is not an RX070, the record does not support a fit.

Screw replacement: match the receiver, then match the set

Receiver screws are easy to overlook until one works loose. The supplied record confirms a set of four screws for RX070 receivers and nothing more: no thread specification, no torque value, and no installation sequence. Those details are not confirmed by the supplied information, so do not substitute hardware-store screws on the assumption they are equivalent.

Before ordering, check the receiver model marking. If it is an RX070, the four-screw set is the supported replacement. If it is a different receiver, the record does not establish compatibility, and the right move is to identify the correct part rather than force a fit. When you do replace screws, keep the set together so you are not mixing old and new hardware across the housing.

A parts-care routine that respects the limits

  • Inspect before each season: Check the antenna for bends or looseness, the receiver gasket for flattening or gaps, and the receiver screws for missing pieces. These are visual and tactile checks, not measurements.
  • Confirm the model before you order: The antenna record covers all Educator models. The gasket record names the large RX120. The screw record names the RX070. Order against the model, not against the symptom.
  • Keep spares of the consumable parts: The antenna, gasket, and screw set are inexpensive relative to a lost training day. The catalog prices for these parts are low, and the antenna is also listed with a comparison price, so stocking a spare is a practical hedge rather than an upsell.
  • Do not invent a procedure: The supplied records do not include installation steps, torque values, or cleaning instructions for these parts. Use the guidance that came with your system, and treat any unconfirmed step as something to verify rather than assume.

Where these parts fit in the wider parts catalog

These three parts are a narrow slice of the replacement-parts range. The same catalog also lists an RX-090 small receiver, which is a receiver rather than a part, and the records note that other replacement dog collar parts are available. If your issue is not the antenna, the RX120 gasket, or the RX070 screws, the next step is to identify the failing component and match it to the correct listing rather than adapting one of these three.

One honest tradeoff: buying a part that is close but not confirmed for your model can cost more in time and frustration than the part itself. The records are specific for a reason. Use the model name as the deciding factor, and when the supplied information does not confirm a fit, treat that as a signal to check further rather than a green light.

Související články

Customer Service
Domů
Produkty
Košík
Profil