Small parts do two jobs: seal and fasten
The rubber plug, receiver gasket and round-transmitter screws are not accessories you notice until one goes missing. Each has a narrow job: the plug closes an opening on a large transmitter, the gasket sits in a fencing receiver, and the screws hold a round transmitter together. Treat them as wear items and check them before a session rather than after a failure.
The supplied catalog records confirm fit for these three parts but do not include installation steps, torque values, or cleaning procedures. Use the fit notes below to choose the right part, then follow the instructions that came with your device for anything beyond a visual check.
The replacement rubber plug for large transmitters
- Replacement Rubber Plug for Large Transmitter 400, 800 & 1200 Series: Replacement Rubber Plug for Large Transmitter 400, 800 & 1200 Series The name ties this plug to three large-transmitter series, so start by confirming your transmitter belongs to the 400, 800 or 1200 family before ordering.

Replacement Rubber Plug for Large Transmitter 400, 800 & 1200 Series - Replacement Rubber Plug for Large Transmitter 400, 800 & 1200 Series: Catalog price: USD 1.58 (comparison price USD 3.15) A low-cost spare makes sense to keep on hand, but price alone does not confirm fit; the series match does.
What to check on the plug before you replace it
- Confirm the transmitter series: The supplied record names the 400, 800 and 1200 Series. If your transmitter is outside those series, the supplied information does not confirm this plug fits.
- Look for a missing or loose plug: A plug that no longer stays seated is the clearest reason to reach for a replacement. The supplied record does not describe a cleaning or lubrication routine, so avoid inventing one.
- Keep the old plug as a reference: Compare the replacement with the part you removed before fitting it. The record lists one Standard variant and does not supply dimensions, so a side-by-side check is the practical confirmation.
The gasket for fencing receivers
- GASKET FOR FENCING RECEIVERS ( 1 ): GASKET FOR FENCING RECEIVERS ( 1 ) The name limits this gasket to fencing receivers and indicates a single gasket, so order the quantity you need rather than assuming a multi-pack.

GASKET FOR FENCING RECEIVERS ( 1 ) - GASKET FOR FENCING RECEIVERS ( 1 ): Catalog price: USD 1.05 (comparison price USD 2.10) An inexpensive single gasket is easy to add to a parts order, but the receiver type is the deciding factor.
Gasket fit: receiver type first, then condition
- Match the receiver family: This gasket is listed for fencing receivers. The supplied record does not name specific receiver models, so check your receiver's documentation or the part you are replacing before ordering.
- Inspect for a flattened or displaced gasket: A gasket that no longer sits flat is the visible sign that replacement is worth considering. The supplied record does not include a replacement procedure or a recommended service interval.
- Do not substitute a transmitter plug for a receiver gasket: The plug is listed for large transmitters and the gasket for fencing receivers. They are separate parts with separate listings, and the supplied information does not support swapping them.
The screws for small and large round transmitters
- SCREWS FOR SMALL AND LARGE ROUND TRANSMITTERS ( SET OF 6 ): SCREWS FOR SMALL AND LARGE ROUND TRANSMITTERS ( SET OF 6 ) The set covers both small and large round transmitters and supplies six screws, so one order can cover a transmitter that uses several fasteners.
- SCREWS FOR SMALL AND LARGE ROUND TRANSMITTERS ( SET OF 6 ): Catalog price: USD 0.28 (comparison price USD 0.55) A six-piece set at this price is a sensible spare to keep with your training kit, provided your transmitter is a round model.
A simple parts-care routine before each session
This routine uses only what the supplied records support: identifying the part, checking that it is seated, and replacing it when it is not. It does not replace your device manual.
- Identify the part and its location: Plug on a large 400, 800 or 1200 Series transmitter; gasket in a fencing receiver; screws on a small or large round transmitter.
- Check seating with a visual inspection: Confirm the plug is in place, the gasket sits flat, and the screws are present. The supplied records do not give torque values, so do not tighten beyond what the device instructions specify.
- Replace rather than improvise: If a part is missing or visibly displaced, fit the matching replacement from the catalog. The supplied information does not confirm that hardware-store substitutes will seal or fit correctly.
- Store spares together: Keep the plug, gasket and screw set in one labeled bag with your training gear so a missing part does not end a session.
Where the supplied information stops
These records confirm product names, series or receiver type, quantity where stated, and catalog prices. They do not include dimensions, materials, installation instructions, cleaning agents, or waterproofing test results. Any claim that a part is waterproof beyond its listed purpose would go beyond the evidence.
That gap is not a reason to avoid the parts; it is a reason to use the fit information that is supplied and your device documentation for procedure. If you are unsure which transmitter series or receiver type you own, identify that first, because it is the one detail that decides whether each part is the right one.



